All guides

Why Your Signature Upload Gets Rejected, and How to Fix It

Why online forms reject a scanned signature, from paper, pen and lighting to cropping, KB size, pixel size and file type, and how to fix each one.

By Pix2Doc Team,

A signature looks like the easiest part of an online application. Then the portal says "invalid file", "file size not within range" or, worse, the form is accepted and later marked as having an unclear signature. Most of these problems come from a handful of small things. This guide goes through them in the order you'd meet them, from the pen on paper to the file you upload.

Start with the right paper and pen

The cleaner the original, the easier everything else becomes.

  • Use plain white paper. Ruled notebook paper adds lines that show up in the scan and can look like part of your signature.
  • Use a black or dark blue pen with a medium tip. Many forms ask for black ink specifically, so check your instructions. A very fine pen or a pencil gives faint lines that disappear when the image is made small.
  • Sign normally, at your usual size, inside a box about the size of the space on a paper form. Don't write in capitals unless the form asks for it, and sign the same way you will sign on paper later. Some recruitment processes compare signatures at later stages.
  • Sign a few times and pick the cleanest one.

Take the photo in good light

You don't need a scanner. A phone camera works well if the light is right.

  1. Put the paper on a flat surface near a window during the day, or under a bright ceiling light.
  2. Hold the phone directly above the paper, parallel to it, so the signature isn't slanted or stretched.
  3. Make sure your phone and hand don't cast a shadow across the paper.
  4. Turn the flash off. Flash tends to create a bright spot and a dark edge on white paper.
  5. Tap on the signature to focus before taking the photo.

The result should show dark ink on paper that looks white or light grey, not yellow or blue-grey.

Crop tight around the signature

A common reason for rejection is too much empty paper around the signature. The verifier sees a tiny scribble in a big white box, and the portal's preview may shrink it until it's unreadable.

Open the photo in Crop Image and crop close to the edges of your signature, leaving only a small margin on each side. Signatures are wide and short, so the cropped image should be a wide rectangle. If the form gives a specific shape in pixels, for example a width noticeably larger than the height, crop to roughly that shape so your signature isn't squashed when resized.

Make the background white

Grey or shadowed paper is a frequent complaint on signature checks. The best fix is at the photo stage: good daylight and no shadow. If the paper still looks grey, open the photo in your phone's built-in editor and raise the brightness or exposure a little, and the contrast, until the paper looks white but the ink lines are still solid. Push it too far and thin strokes start to break up.

Don't remove the background to make it transparent. Most portals want a JPG, and JPG has no transparency. The Resize Signature tool fills any transparent areas with white rather than black, but it doesn't brighten grey paper for you, so sort out the lighting first.

Get the size right in KB and in pixels

Forms usually state two things, and both are checked:

  • File size in KB, for example "10 KB to 20 KB". Too big is rejected, and so is too small if there is a minimum.
  • Dimensions in pixels or cm, for example a specific width and height.

To meet both:

  1. Open Resize Signature. It starts with a 10–20 KB target and 300 × 100 pixels, a common combination, but change both if your form says something different.
  2. Choose your cropped signature photo.
  3. If the form gives pixel dimensions, enter them exactly. If it gives cm, enter the cm values. When you set an exact size, the tool trims evenly from the edges to match that shape, which is another reason to crop to roughly the right shape first.
  4. Run the tool. It finds the highest quality that fits your KB range and gives you a JPG.
  5. Zoom in on the result. Every stroke of the signature should be visible and connected.

If you need a different range, Resize Image to KB lets you set any range and size. For exam forms, Exam Photo and Signature Resizer has presets with links to where the numbers came from. Always compare those with the official notice for your exam; our guide on photo and signature sizes for SSC, UPSC, IBPS and NEET explains why.

Save it as JPG

Most application forms accept only JPG or JPEG for signatures. JPG and JPEG are the same thing. Watch out for:

  • PNG files, which phones often create when you screenshot or edit an image.
  • HEIC files from iPhones, which many portals don't accept at all.
  • PDFs of a scanned signature, unless the form specifically asks for a PDF.

The resizer tools on this site save as JPG, so the output is ready to upload.

Quick fixes for common error messages

  • "File size should be between X and Y KB": set that exact range in the resizer and run it again from the original photo, not from an already compressed copy.
  • "Invalid dimensions": enter the pixel width and height from the instructions.
  • "Invalid file format": make sure the file ends in .jpg or .jpeg. Renaming a PNG to .jpg is not the same as converting it, and some portals detect this.
  • Signature unclear or not visible: go back to the paper. Use a darker pen, better light and a tighter crop, then resize again.

Your file is processed in your browser on every Pix2Doc tool, so your signature never leaves your device. That's worth caring about with something that can be misused.